[Apr 30, 2025] Fortinet Dumps - Learn How To Deal With The (FCP_FAZ_AD-7.4) Exam Anxiety
DEMO FREE BEFORE YOU BUY FCP_FAZ_AD-7.4 DUMPS
Fortinet FCP_FAZ_AD-7.4 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
NEW QUESTION # 82
What is the best approach to handle a hard disk failure on a FortiAnalyzer that supports hardware RAID?
- A. Shut down FortiAnalyzer and replace the disk.
- B. There is no need to do anything because the disk will self-recover.
- C. Run execute format disk to format and restart the FortiAnalyzer device.
- D. Perform a hot swap of the disk.
Answer: D
Explanation:
In a hardware RAID setup, FortiAnalyzer supports hot swapping, which allows you to replace a failed disk without shutting down the device. The RAID controller will automatically rebuild the array using the new disk, minimizing downtime and maintaining data integrity.
NEW QUESTION # 83
For proper log correlation between the logging devices and FortiAnalyzer, FortiAnalyzer and all registered devices should:
- A. Use DNS
- B. Use an NTP server
- C. Use real-time forwarding
- D. Use host name resolution
Answer: B
NEW QUESTION # 84
Refer to the exhibits.
How many events will be added to the incident created after running this playbook?
- A. Thirteen events will be added.
- B. No events will be added.
- C. Five events will be added.
- D. Ten events will be added.
Answer: A
NEW QUESTION # 85
In a Fortinet Security Fabric, what can make an upstream FortiGate create traffic logs associated with sessions initiated on downstream FortiGate devices?
- A. The downstream device cannot connect to FortiAnalyzer.
- B. The upstream FortiGate is configured to do NAT.
- C. Log redundancy is configured in the fabric.
- D. The traffic destination is another FoitiGate in the fabric.
Answer: A
Explanation:
In the Fortinet secure fabric, the scenario for having the upstream FortiGate create a traffic log associated with a session initiated on the downstream FortiGate appliance is: The upstream FortiGate is configured with Network Address Translation (NAT).
When the upstream FortiGate performs NAT for sessions initiated on downstream devices, it creates logs for those NAT-processed sessions. This is because the upstream device is responsible for providing public network egress for these sessions and logging traffic information.
NEW QUESTION # 86
If the primary FortiAnalyzer in an HA cluster fails, how is the new primary elected?
- A. The firmware version is checked first.
- B. The configured IP address is checked first.
- C. The configured priority is checked first
- D. The active port number is checked first.
Answer: C
Explanation:
In the case of a primary device failure, FortiAnalyzer HA uses the following rules to select a new primary:
* All cluster devices are assigned a priority from 80 to 120. The default priority is 100. If the primary device becomes unavailable, the device with the highest priority is selected as the new primary device. For example, a device with a priority of 110 is selected over a device with a priority of 100.
* If multiple devices have the same priority, the device whose primary IP address has the greatest value is selected as the new primary device. For example, 123.45.67.124 is selected over 123.45.67.123.
* If a new device with a higher priority or a greater value IP address joins the cluster, the new device does not replace (or pre-empt) the current primary device automatically.
FortiAnalyzer_7.0_Study_Guide-Online page 62
NEW QUESTION # 87
In FortiAnalyzer's FormView, source and destination IP addresses from FortiGate devices are not resolving to a hostname. How can you resolve the source and destination IPs, without introducing any additional performance impact to FortiAnalyzer?
- A. Resolve IPs on FortiGate
- B. Configure local DNS servers on FortiAnalyzer
- C. Resolve IPs on a per-ADOM basis to reduce delay on FortiView while IPs resolve
- D. Configure # set resolve-ip enable in the system FortiView settings
Answer: A
NEW QUESTION # 88
How do you restrict an administrator's access to a subset of your organization's ADOMs?
- A. Assign the ADOMs to the administrator's account
- B. Set the ADOM mode to Advanced
- C. Assign the default Super_User administrator profile
- D. Configure trusted hosts
Answer: A
Explanation:
https://docs.fortinet.com/document/fortianalyzer/6.2.5/administration-guide/717578/assigning-administrators-to-an-adom
NEW QUESTION # 89
Which two statements are true regarding FortiAnalyzer log forwarding? (Choose two.)
- A. Both modes, forwarding and aggregation, support encryption of logs between devices.
- B. Forwarding mode forwards logs in real time only to other FortiAnalyzer devices.
- C. Aggregation mode stores logs and content files and uploads them to another FortiAnalyzer device at a scheduled time.
- D. In aggregation mode, you can forward logs to syslog and CEF servers as well.
Answer: A,C
Explanation:
A) FortiAnalyzer_7.0_Study_Guide-Online.pdf page 148: The log communication between devices can be protected by encryption, with the desired encryption level, using the commands shown on the slide. (You need to interpret this. "Real time" and "aggregation" is about the "moment" when Fortigate sends the logs. However, no matter the moment, Fortigate will upload logs encrypted or unencrypted based on previous / differente config).
C) FortiAnalyzer_7.0_Study_Guide-Online.pdf page 147: Aggregation: Logs and content files stored and uploaded at scheduled time.
NEW QUESTION # 90
On the RAID management page, the disk status is listed as Initializing.
What does the status Initializing indicate about what the FortiAnalyzer is currently doing?
- A. FortiAnalyzer is functioning normally
- B. FortiAnalyzer is writing data to a newly added hard drive to restore it to an optimal state
- C. FortiAnalyzer is ensuring that the parity data of a redundant drive is valid
- D. FortiAnalyzer is writing to all of its hard drives to make the array fault tolerant
Answer: D
Explanation:
Reference:
8977-00505692583a/FortiAnalyzer-5.6.10-Administration-Guide.pdf (40)
NEW QUESTION # 91
Refer to the exhibit.
The capture displayed was taken on a FortiAnalyzer.
Why is a single IP address shown as the source for all logs received?
- A. The device sending logs has two VDOMs in the same ADOM.
- B. FortiAnalyzer is receiving logs from the root FortiGate of a Security Fabric.
- C. The logs belong to devices that are part of a high availability (HA) cluster.
- D. FortiAnalyzer is using the device MAC addresses to differentiate their logs.
Answer: B
Explanation:
In a Fortinet Security Fabric, logs from downstream devices can be sent to FortiAnalyzer through the root FortiGate. This is why all the logs have the same source IP address (the root FortiGate). The root FortiGate aggregates and forwards the logs from all downstream devices, so the source IP in the log capture will appear to be from the root FortiGate itself, even though the logs originate from multiple devices within the fabric.
NEW QUESTION # 92
What are two benefits of using fabric connectors? (Choose two.)
- A. Using fabric connectors is more efficient than using third-party polling with API.
- B. Fabric connectors allow you to improve redundancy.
- C. They allow FortiAnalyzer to send logs in real-time to public cloud accounts.
- D. You do not need an additional license to send logs to the cloud platform.
Answer: B,C
NEW QUESTION # 93
What are analytics logs on FortiAnalyzer?
- A. Logs that are compressed and saved to a log file
- B. Logs that are indexed and stored in the SQL
- C. Logs that roll over when the log file reaches a specific size
- D. Logs classified as type Traffic, or type Security
Answer: B
Explanation:
On FortiAnalyzer, analytics logs refer to the logs that have been processed, indexed, and then stored in the SQL database. This process allows for efficient data retrieval and analytics. Unlike basic log storage, which might involve simple compression and storage in a file system, analytics logs in FortiAnalyzer undergo an indexing process. This enables advanced features such as quick search, report generation, and detailed analysis, making it easier for administrators to gain insights into network activities and security incidents.
Reference: FortiAnalyzer 7.2 Administrator Guide - "Log Management" and "Data Analytics" sections.
NEW QUESTION # 94
Which two settings must you configure on FortiAnalyzer to allow non-local administrators to authenticate to FortiAnalyzer with any user account in a single LDAP group? (Choose two.)
- A. A trusted host profile that restricts access to the LDAP group
- B. An administrator group
- C. A remote LDAP server
- D. A local wildcard administrator account
Answer: C,D
NEW QUESTION # 95
An administrator, fortinet, can view logs and perform device management tasks, such as adding and removing registered devices. However, administrator fortinet is not able to create a mail server that can be used to send alert emails.
What can be the problem?
- A. fortinet is assigned Restricted_User administrative profile.
- B. A trusted host is configured.
- C. ADOM mode is configured with Advanced mode.
- D. fortinet is assigned the Standard_User administrative profile.
Answer: D
Explanation:
Administrator Fornetet is able to view logs and perform device management tasks such as adding and removing registered devices, but cannot create a mail server to send alert mails. The causes of this problem are:
fortinet is assigned a Restricted_User administrative rights profile.
Administrators who are assigned as Restricted_User have restricted access, which may include viewing logs and performing certain device management tasks, but not more advanced administrative functions such as configuring mail servers. Such permission restrictions prevent them from performing configuration changes that require higher permissions.
NEW QUESTION # 96
An administrator has configured the following settings:
What is the purpose of executing these commands?
- A. To create the secure channel used by the OFTP process.
- B. To record the hash value and authentication code of log files.
- C. To encrypt log transfer between FortiAnalyzer and other devices.
- D. To verify the integrity of the log files received.
Answer: B
Explanation:
The command set log-checksum md5-auth configures FortiAnalyzer to generate an MD5 hash for each log file, along with an authentication code. This ensures that the integrity of the logs can be verified, confirming that the logs have not been tampered with.
NEW QUESTION # 97
Refer to the exhibit.
Which image corresponds to the packet capture shown in the exhibit?
- A.
- B.
- C.
- D.
Answer: A
Explanation:
Chosen image shows the device Remote-FortiGate with the IP 10.200.3.1 and a connection status of "Connection Up," which is consistent with the packet capture details showing active communication between the client and server.
NEW QUESTION # 98
Which statement describes online logs on FortiAnalyzer?
- A. Logs that can be viewed using Log Browse
- B. Logs that reached a specific size and were rolled over
- C. Logs that are saved to disk, compressed, and available in FortiView
- D. Logs that can be used to create reports
Answer: D
NEW QUESTION # 99
......
Latest Fortinet FCP_FAZ_AD-7.4 Dumps with Test Engine and PDF: https://www.passexamdumps.com/FCP_FAZ_AD-7.4-valid-exam-dumps.html
Now, get the NEWEST FCP_FAZ_AD-7.4 dumps in Test Engine from: https://drive.google.com/open?id=1OWSlp_XDAeCrLSk9_T6qSJnSx7UVvxUj
