Latest 300-430 Pass Guaranteed Exam Dumps Certification Sample Questions
New 300-430 Test Materials & Valid 300-430 Test Engine
Monitoring
This domain makes up about 15% of the whole content and evaluates the individuals’ understanding of the following processes:
- Troubleshooting the client’s connectivity.
- Managing rogues and alarms;
- Managing RF interferers;
- Utilizing reports on Cisco DNA Center and PI;
NEW QUESTION 11
Refer to the exhibit. An engineer must connect a fork lift via a WGB to a wireless network and must authenticate the WGB certificate against the RADIUS server. Which three steps are required for this configuration? (Choose three.)
- A. Configure the certificate on the WLC.
- B. Configure the certificate, WLAN, and radio interface on WGB.
- C. Configure the access point with the root certificate from ISE.
- D. Configure a policy on ISE to allow devices to connect that validate the certificate.
- E. Configure WGB as a network device in ISE.
- F. Configure WLAN to authenticate using ISE.
Answer: B,D,F
NEW QUESTION 12
A customer has a distributed wireless deployment model where the WLCs are located in the data centers.
Because the file servers are located in the data center, the traffic from the corporate WLAN
"Corp-401266017" must go through the controllers, where the guest WLAN "Guest-19283746" traffic must use the local Internet line installed in each office. Which configuration will accomplish this task?
- A. Enable Local Switching for the corporate and guest WLAN.
- B. Disable Local Switching for the corporate WLAN and enable it for the guest WLAN.
- C. Enable Local Switching for the corporate WLAN and disable it for the guest WLAN.
- D. Disable Local Switching for the corporate and guest WLAN.
Answer: A
NEW QUESTION 13
Which command set configures a Cisco Catalyst 9800 Series Wireless Controller so that the client traffic enters the network at the AP switch port?
- A. Option A
- B. Option C
- C. Option B
- D. Option D
Answer: D
Explanation:
Note: To enable Local switching, you have to disable central switching
NEW QUESTION 14
What is the default NMSP echo interval between Cisco MSE and a Wireless LAN Controller?
- A. 60 seconds
- B. 30 seconds
- C. 15 seconds
- D. 10 seconds
Answer: C
Explanation:
NEW QUESTION 15
A customer has a distributed wireless deployment model where the WLCs are located in the data centers.
Because the file servers are located in the data center, the traffic from the corporate WLAN
"Corp-401266017" must go through the controllers, where the guest WLAN "Guest-19283746" traffic must use the local Internet line installed in each office. Which configuration will accomplish this task?
- A. Enable Local Switching for the corporate and guest WLAN.
- B. Disable Local Switching for the corporate WLAN and enable it for the guest WLAN.
- C. Enable Local Switching for the corporate WLAN and disable it for the guest WLAN.
- D. Disable Local Switching for the corporate and guest WLAN.
Answer: C
NEW QUESTION 16
An engineer must track guest traffic flow using the WLAN infrastructure. Which Cisco CMX feature must be configured and used to accomplish this tracking?
- A. detect and locate.
- B. connect and engage
- C. presence
- D. analytics
Answer: C
Explanation:
Explanation
The Cisco CMX Presence Analytics service is a comprehensive analytics and engagement platform that uses APs to detect visitor presence based on their mobile devices' Received Signal Strength Indication (RSSI). The AP detects these client mobile devices irrespective of the latter's wireless association state as long as they are within the specified signal range, and the wireless option is enabled on the mobile device (ability to detect devices wirelessly even if they are not connected to the network
https://www.cisco.com/c/en/us/td/docs/wireless/mse/10-4/cmx_config/b_cg_cmx104/the_cisco_cmx_presence_a
NEW QUESTION 17
An engineer completed the basic installation for two Cisco CMX servers and is in the process of configuring high availability, but it fails. Which two statements about the root of the issue are true? (Choose two.)
- A. The types of the primary and secondary Cisco CMX installations differ.
- B. Both Cisco CMX installations are virtual.
- C. The delay between the primary and secondary instance is 200 ms.
- D. The Cisco CMX instances are installed in the same subnet.
- E. The sizes of the primary and secondary Cisco CMX installations differ.
Answer: A,E
NEW QUESTION 18
Which QoS level is recommended for guest services?
- A. bronze
- B. gold
- C. platinum
- D. silver
Answer: A
Explanation:
NEW QUESTION 19
Refer to the exhibit.
An engineer needs to manage non-802.11 interference. What is observed in the output on PI?
- A. The three Individual clusters shown Indicate poor AP placement.
- B. Several light interferers are collectively impacting connectivity at this site.
- C. At least one strong interferer is impacting connectivity at this site.
Answer: A
NEW QUESTION 20
An engineer set up identity-based networking with ISE and configured AAA override on the WLAN. Which two attributes must be used to change the client behavior from the default settings? (Choose two.)
- A. DHCP timeout
- B. DNS server
- C. multicast address
- D. DSCP value
- E. IPv6 ACL
Answer: D,E
NEW QUESTION 21
Which three characteristics of a rogue AP pose a high security risk? (Choose three.)
- A. low RSSI
- B. foreign SSID
- C. open authentication
- D. accepts clients
- E. distant location
- F. high RSSI
Answer: B,C,D
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/wireless/controller/74/configuration/guides/consolidated/b_cg74_CONSO
NEW QUESTION 22
Refer to the exhibit.
An engineer must connect a fork lift via a WGB to a wireless network and must authenticate the WGB certificate against the RADIUS server. Which three steps are required for this configuration? (Choose three.)
- A. Configure the certificate on the WLC.
- B. Configure the certificate, WLAN, and radio interface on WGB.
- C. Configure the access point with the root certificate from ISE.
- D. Configure a policy on ISE to allow devices to connect that validate the certificate.
- E. Configure WGB as a network device in ISE.
- F. Configure WLAN to authenticate using ISE.
Answer: B,D,F
NEW QUESTION 23
Which command set configures a Cisco Catalyst 9800 Series Wireless Controller so that the client traffic enters the network at the AP switch port?
- A. Option B
- B. Option A
- C. Option C
- D. Option D
Answer: A
NEW QUESTION 24
The network management team in a large shopping center has detected numerous roque APs from local coffee shops that are broadcasting SSIDs. All of these SSlDs have names starting with ATC (for example. ATC302.
ATC011. and ATC566). A wireless network engineer must appropriately classify these SSIDs using the Rogue Rules feature. Drag and drop the options from the left onto the categories in which they must be used on the right. Not all options are used.
Answer:
Explanation:
NEW QUESTION 25
An engineer wants the wireless voice traffic class of service to be used to determine the queue order for packets received, and then have the differentiated services code point set to match when it is resent to another port on the switch. Which configuration is required in the network?
- A. WMM set to required on the WLAN
- B. Platinum QoS configured on the WLAN
- C. msl qos trust cos configured on the controller switch port
- D. msl qos trust dscp configured on the controller switch port
Answer: D
NEW QUESTION 26
......
300-430 Sample with Accurate & Updated Questions: https://www.passexamdumps.com/300-430-valid-exam-dumps.html
300-430 Updated Exam Dumps [2022] Practice Valid Exam Dumps Question: https://drive.google.com/open?id=11EMMEXtP2qvTHmT8h3q0MEy47yFyo5LB
