[2024] New 300-610 exam dumps Use Updated Cisco Exam
Verified 300-610 Dumps Q&As - 300-610 Test Engine with Correct Answers
Cisco 300-610 exam is a certification exam designed for professionals who are interested in becoming experts in designing Cisco Data Center Infrastructure. Being certified in 300-610 exam will not only increase your knowledge in Cisco Data Center Infrastructure but also give you a competitive edge in the job market. Therefore, if you are interested in becoming a Cisco Data Center Infrastructure expert, 300-610 exam is an excellent way to start.
Earning the Cisco 300-610 certification demonstrates that the candidate has the knowledge and skills required to design data center infrastructure using Cisco technologies. Designing Cisco Data Center Infrastructure certification can help professionals advance their career in data center design and implementation, as well as increase their earning potential. Additionally, with the growing demand for data center professionals, obtaining this certification can help candidates stand out in a competitive job market.
Who Should Aim at Cisco 300-610?
Cisco 300-610 is clearly not for everyone. It is for those willing to make big in the data center management industry. Thus, data center engineers as well as data center architects are the targeted job roles for this test.
Speaking of compulsory prerequisites, there are none. However, the word of wise says that it is good to have three to five years of practical experience in generating data center solutions. In this case, the certification journey will be a lot more simplified.
NEW QUESTION # 88
Which two methods mitigate congestion in a SAN network? (Choose two.)
- A. Configure the port channel to enable individual buffer-to-buffer credits.
- B. Configure ER_RDY to allow splitting of each ISL between switches into separate virtual links.
- C. Configure the flow control for the FC to use R_RDY.
- D. Use the port-monitor command to detect slow drain devices.
- E. Configure the port monitor to allow categorization of a specific device as slow.
Answer: D,E
Explanation:
Section: Storage Network Design
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/8_x/config/interfaces/ cisco_mds9000_interfaces_config_guide_8x/congestion_avoidance_isolation.html
NEW QUESTION # 89
Which two naming formats identify target or initiator iSCSI nodes? (Choose two.)
- A. WWN
- B. IQN
- C. OUI
- D. EUI
- E. WWPN
Answer: A,B
Explanation:
Section: Storage Network Design
Explanation/Reference: https://www.cisco.com/en/US/docs/storage/san_switches/mds9000/sw/rel_3_x/configuration/ guides/cli_3_3_1/ciscsi.html
NEW QUESTION # 90
A network engineer is designing a Cisco Hyperflex infrastructure. The infrastructure will be connected to an external SAN fiber channel array and must support Microsoft clustering.
Which storage connectivity method must be used to meet these requirements?
- A. Internet Small Computer Systems Interface
- B. server message block
- C. Fibre Channel over Ethernet
- D. raw device mapping
Answer: C
Explanation:
Reference:
HyperFlex_HX_DataPlatformSoftware/Network_External_Storage_Management_Guide/ b_HyperFlex_Systems_Network_and_External_Storage_Management_Guide_3_0/ b_HyperFlex_Systems_Network_and_External_Storage_Management_Guide_3_0_chapter_010.html
NEW QUESTION # 91
Which two naming formats identify target or initiator iSCSI nodes? (Choose two.)
- A. IQN
- B. EUI
- C. WWN
- D. OUI
- E. WWPN
Answer: A,B
Explanation:
https://docs.vmware.com/en/VMware-vSphere/5.5/com.vmware.vsphere.storage.doc/GUID-686D92B6-A2B2-4944-8718-F1B74F6A2C53.html
NEW QUESTION # 92
Drag and drop the data center technologies from the left onto the correct descriptions on the right. Not all technologies are used.
Answer:
Explanation:
NEW QUESTION # 93
A network engineer must design a data center network with four Cisco Nexus 7706 switches. The switches will be installed in primary and secondary data centers in vPC domains. The two data centers must be connected via Layer 2 links and provide the maximum throughput, redundancy, and avoid port-blocking spanning-tree design.
Which deployment model meets these requirements?
- A. dual-sided dual vPC
- B. single-sided single vPC
- C. single-sided dual vPC
- D. dual-sided single vPC
Answer: A
NEW QUESTION # 94
An engineer designs a Cisco UCS solution that must provide guaranteed and deterministic bandwidth to a specific server in the environment. The solution must apply to network and storage traffic of C-Series and B-Series servers. Which solution should be included to meet these requirements?
- A. Pin the server ports of the service profile to dedicates uplink ports.
- B. Pin the vNlCs and vHBAs of the service profile to dedicated server ports
- C. Pin the IOM ports of the service profile to dedicated server ports.
- D. Pin the vNICs and the vHBAs of the service profile to dedicated uplink ports.
Answer: D
Explanation:
Reference:
NEW QUESTION # 95
DRAG DROP
Drag and drop the feature descriptions from the left onto the correct UCS Fabric Interconnect modes on the right.
Select and Place:
Answer:
Explanation:
Section: Compute Design
Explanation/Reference: https://www.cisco.com/c/en/us/solutions/collateral/data-center-virtualization/unified-computing/ whitepaper_c11-701962.html
NEW QUESTION # 96
A network engineer must design a Cisco HyperFlex solution based on these requirements:
* two clusters in the main data center consisting of five HyperFlex nodes
* one edge node for the remote branch
* cluster nodes that use one rack unit of space
Which two devices should be used in the remote branch cluster for this design? (Choose two.)
- A. HX240C
- B. UCSB B200
- C. Gigabit Ethernet Switch
- D. Fabric Interconnect 6300
- E. HX220C
Answer: C,E
NEW QUESTION # 97
An engineer must design a VXLAN EVPN network. The solution should optimize broadcast, unknown unicast, and multicast (BUM) and short BUM replication, and use PIM anycast RP. Which solution should be included in the design?
- A. ingress replication
- B. head-end replication
- C. PIM sparse mode
- D. PIM dense mode
Answer: C
NEW QUESTION # 98
Which feature provides a sandbox to convert NX-OS CLI commands to REST-based scripts on Cisco Nexus
7700 Series Switches?
- A. Postman
- B. Guest shell
- C. NX-API
- D. Bash shell
Answer: C
NEW QUESTION # 99
Refer to the exhibit. A Cisco engineer is configuring a customer scenario with 2 x MDS 9000 switches 24 x UCS B200M6 blade servers. UCS 64S4 Fabric Interconnect in end-host mode and 3 x UCS 5108 server chassis with 2408 Fabric Extenders The engineer installs 6 x SQL Server 2019 on all blades and then notices that there are read and write latencies What is the best way to balance the utilization across the shared ports?
- A. Enable "Only dedicate rate mode
- B. Change the assigned speed to 8 Gbps Auto.
- C. Disable restrictions on oversubscription ratios
- D. Set 4 Gbps performance buffers
Answer: C
Explanation:
Reference:
When restrictions on oversubscription ratios are disabled, the bandwidth allocation among the shared ports is proportionate to the configured speed. (If the configured speed is auto, then bandwidth is allocated assuming a speed of 4 Gbps.) For example, if you have three shared ports configured at 1, 2, and 4 Gbps, then the allocated bandwidth ratio is 1:2:4. In Cisco SAN-OS Release 3.0 and later (or when restrictions on oversubscription ratios are enabled), port bandwidths are allocated in equal proportions, regardless of port speed, so, the bandwidth allocation for the same three ports mentioned in the example would be 1:1:1.
NEW QUESTION # 100
An engineer manages a multi-organization Cisco UCS fabric and requires a solution to streamline the daily operational tasks of creating service profile templates. The operations team is unfamiliar with programming languages and must have a solution that is written in an easy-to-read and declarative manner. The operations team also requires the tool to be flexible enough to support the creation of custom modules. The development team is familiar with the Python programming language and can develop these custom modules for the operations team. Which tool meets these requirements?
- A. Puppet
- B. Ansible
- C. CFEngine
- D. Chef
Answer: B
NEW QUESTION # 101
A network consultant proposes that the configuration of the Cisco UCS servers be based on service templates to facilitate the UCS infrastructure operation. The service profiles must remain connected to the template and be modified when the template settings are changed.
Which configuration meets these requirements?
- A. service profile template with type set to Initial
- B. service profile with type set to Local
- C. service profile template with type set to Updating
- D. service profile with type set to Global
Answer: C
NEW QUESTION # 102
Which address pool is used when a vHBA template is created?
- A. MAC
- B. UUID
- C. IP
- D. WWPN
Answer: D
Explanation:
Section: Automation Design
Explanation
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/gui/config/guide/2-1/ b_UCSM_GUI_Configuration_Guide_2_1/b_UCSM_GUI_Configuration_Guide_2_1_chapter_011010.html
NEW QUESTION # 103
A company must introduce a scalable network automation tool to deploy, configure, and manage thousands of network devices and servers. The company servers already have been security-hardened and must not have any additional software installed on them. The security policy mandates the use of a secure communication protocol that supports authentication and encryption for managing the servers.
Which two automation tools must be used to meet these requirements? (Choose two.)
- A. Puppet
- B. SaltStack
- C. Ansible
- D. CFEngine
- E. Chef
Answer: A,B
NEW QUESTION # 104
When planning to deploy a load-balancing service as a managed node, which ACI configuration must be included?
- A. BGP ECMP
- B. inline load-balancing device
- C. ITD
- D. Layer 4 to Layer 7 device package
Answer: D
Explanation:
Section: Network Design
Explanation
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/1-x/ACI_Best_Practices/ b_ACI_Best_Practices/b_ACI_Best_Practices_chapter_0110.html
NEW QUESTION # 105
What are two functions of a Network Services Orchestrator in an NFV environment? (Choose two.)
- A. It operates at the resource-facing services layer and provides overall lifecycle management at the network service level.
- B. It provides a standards-based northbound interface for transparent integration with systems that operate at the customer-facing services layer.
- C. It operates at the customer-facing services layer and provides the management interface for the virtual network devices.
- D. It provides an API-based northbound interface for transparent integration with systems that operate at the resource-facing services layer.
- E. It provides a standards-based southbound interface for transparent integration with systems that operate at the customer-facing services layer.
Answer: A,D
Explanation:
Section: Automation Design
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/net_mgmt/msx/3_4/solution_overview/ Cisco_VMS_Sol_Overview.pdf
NEW QUESTION # 106
Drag the requirements from the left onto the correct policy types on the right.
Answer:
Explanation:
NEW QUESTION # 107
A network engineer is designing a Cisco Hyperflex infrastructure. The Infrastructure will be connected to an external SAN fiber channel array and must support Microsoft clustering.
Which storage connectivity method must be used to meet these requirements?
- A. Fibre Channel over Ethernet
- B. Internet Small Computer Systems Interface
- C. server message block
- D. raw device mapping
Answer: D
Explanation:
Source is from Cisco Press Hyperconverged Infrastructure Data Centers: Demystifying HCI.
NEW QUESTION # 108
An engineer must design a solution to divide the workload across two different data centers and achieve redundancy in case of the failure of either data center Which solution must the engineer choose?
- A. Cisco Hyperflex ROBO cluster
- B. Cisco Hyperflex edge cluster
- C. single Cisco HyperFlex stretched cluster
- D. single Cisco HyperFlex standard cluster
Answer: C
NEW QUESTION # 109
Drag and drop the configurations from the left onto the correct policies on the right.
Answer:
Explanation:
NEW QUESTION # 110
Drag and drop the Cisco Nexus 7000 Series Switch resources from the left onto the correct groups on the right.
Answer:
Explanation:
NEW QUESTION # 111
A network architect designs a high-availability architecture for the Cisco UCS Fabric interconnects that installed in a data center. The architecture must support clustering and redundancy. Which architecture meets these requirements?
- A. dual connections from port L1 to L2 and one connection from port L2 to L1 with Ethernet cables dual
- B. dual connections from port L1 to L1and one connection from port L1 to L1 with twinax cables
- C. dual connections from port L1 to L1 and one connection from port L2 to L2 with Ethernet cables
- D. dual connections from port L1 to 12 and one connection from port L2 to L1 with twinax cables
Answer: C
Explanation:
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/gui/config/guide/1-0-2/b_GUI_Config_Guide/GUI_Config_Guide_chapter4.pdf
NEW QUESTION # 112
Which two naming formats identify target or initiator iSCSI nodes? (Choose two.)
- A. WWN
- B. IQN
- C. OUI
- D. EUI
- E. WWPN
Answer: A,B
Explanation:
https://docs.vmware.com/en/VMware-vSphere/5.5/com.vmware.vsphere.storage.doc/GUID-686D92B6-A2B2-4944-8718-F1B74F6A2C53.html
NEW QUESTION # 113
......
Pass Your 300-610 Dumps as PDF Updated on 2024 With 206 Questions: https://www.passexamdumps.com/300-610-valid-exam-dumps.html
Cisco 300-610 Real Exam Questions and Answers FREE: https://drive.google.com/open?id=1v-Ac3gFG7rsIodfkopI4YDYldk2yDLzv
